MYE MWC-9 Uživatelský manuál stáhnout pdf (Strana 17)

pb^`lk

All reasonable efforts have been taken to ensure that the information contained herein is accurate

at the date of publication, but no representation or warranty as to the accuracy or completeness

of such information is intended or to be implied by its inclusion herein. Any and all representations

and warranties pertaining to the information and products referred to herein shall be set forth in

pb^ `lk

standard sales order form. In addition, pb^ `lk

reserves the right to make

changes to the contents hereof without notice, therefore it is suggested that at the time of inquiry,

the appropriate sales office or factory be contacted directly for verification of published specifica-

tions and products availability.

REV VI

Even though these procedures appear simple, only qualified techni-

cians should perform the installation and maintenance.

Connectors are designed for installation on one atmosphere vessels.

Contact pb^ `lk

for recommendations if using compensated ves-

sels.

Torque values referenced in this literature assume installation into dry

metal threads. For other applications, please contact pb^`lk

for

recommendations.

BULKHEAD CONNECTOR (BC): The BC may be installed using one

of two methods. The preferred method is to spotface the bulkhead sur-

face and thread the hole, then screw the connector by means of a nut

and washer. The bored hole (or threaded hole) should be free of any

“burrs” and all o-ring sealing surfaces polished to a number 32 finish.

Lubricate the BC o-ring with an appropriate silicone spray or grease

before installing. This lubrication should be applied to form an ade-

quate film. Excessive lubrication is detrimental to the operation of the

connector. Bulkhead nut, if used, should not be over-torqued.

IN-LINE CONNECTOR: Lubricate the sealing areas around the male

pins, using an appropriate silicone spray, or grease lightly.

The tbqJ`lk and jáÅêçtbqJ`lk connectors require very little main-

tenance. They are designed to be used in harsh environments and

thus limited amounts of dirt and grit do not affect their performance.

It is recommended that, upon disconnecting or retrieving the system,

the connectors be cleaned, to storage (if possible, remate with dummy

plugs). Prior to deployment the following maintenance procedure is

recommended:

* CAUTION: The use of some oil-based propellants in spray cans can

cause conductivity problems in neoprene.

Avoid sharp bends in cables. Cables subjected to vibration or exposed

to seawater drag should be adequately clamped to prevent conductor

fatigue and ultimate failure.

e^kaifkd mol`barobp ^ka

pmb`f^i `^m^_fifqfbp

INSTALLATION PROCEDURES

CARE AND MAINTENANCE

CABLE AND CONTINUITY PRESERVATION

Demate the connector set.

Flush connector interface with fresh water (deionized water if avail-

able), remove all dirt, grit and grease.

Inspect for damage in sealing areas, excessive corrosion, debond-

ing of the cable and connector interface and cuts in the cable

jacket.

Apply thin film of dilectric compound (DC) grease, silicon based, to

sealing areas of male connector and across the face of the female

connector*. If the BC is removed from it’s housing then replace

facial o-ring and make sure that o-rings are lubricated and in good

condition.

Mate the connector halves, wipe away any excess grease off the

interface line of the mated set.

pb^`lk

GLOBAL PRODUCTION

Callejon Terrazos #8, Local 2-C,

Las Brisas 1ra. Seccion,

Tijuana, B.C., Mexico C.P. 22610.

TEL: +52 (664) 626-2726

FAX: +52 (664) 686-8922

E-Mail: [email protected]

Website: www.seaconglobal.com

Dial from U.S.A. TEL: +1 (619) 308-7901

TOLL FREE: (888) 562-7072

FAX: +1 (619) 308-7900

pb^`lk

1700 Gillespie Way,

El Cajon, California 92020, USA.

TEL: +1 (619) 562-7071

FAX: +1 (619) 562-9706

E-Mail: [email protected]

Website: www.seaconworldwide.com

pb^`lk US GULF AREA SALES OFFICE

21925 Franz Road, Suite 401,

Katy, Texas 77449, USA.

TEL: +1 (281) 599-3509

FAX: +1 (281) 599-3517

E-Mail: gulfcoastsales@seaconbrantner.com

Website: www.seaconworldwide.com

pb^`lk US EAST COAST SALES OFFICE

50 Airport Road,

Westerly, RI 02891, USA.

TEL: +1 (401) 348-0155

FAX: +1 (401) 348-0227

E-Mail: eastcoastsales@seaconbrantner.com

Website: www.seaconworldwide.com

pb^`lk FLORIDA SALES OFFICE

Building B, Suite 22,

3959 South Nova Road,

Port Orange,

Florida 32127, USA.

TEL: +1 (281) 802-5504

E-Mail: [email protected]

pb^`lk ADVANCED PRODUCTS, LLC

1321 Nelius Road, P.O. Box 767,

Bellville, Texas 77418, USA.

TEL: +1 (979) 865-8846

FAX: +1 (979) 865-8859

E-Mail: [email protected]

Website: www.seacon-ap.com

pb^`lk BRAZIL

Rua Conde de Bonfim 120 sala 212,

Tijuca, Rio de Janeiro,

Brazil, CEP: 20520-053.

TEL: +55 (21) 8849-3336

E-Mail: [email protected]

pb^`lk (europe) LTD

Seacon House, Hewett Road,

Gapton Hall Industrial Estate,

Great Yarmouth, Norfolk, NR31 0RB, UK.

TEL: +44 (0) 1493-652733

FAX: +44 (0) 1493-652840

E-Mail: [email protected]

Website: www.seaconeurope.com

pb^`lk PHOENIX, LLC.

15 Gray Lane, Suite 108,

Hopkinton Industrial Park,

Ashaway, RI 02804, USA.

TEL: +1 (401) 637-4952

FAX: +1 (401) 637-4953

E-Mail: [email protected]

Website: www.seaconphoenixllc.com

pb^`lk

1 2 ... 12 13 14 15 16 17

Komentáře k této Příručce

Žádné komentáře

MYE MWC-9 Uživatelský manuál Strana 17

Komentáře k této Příručce